How to replace a bathroom sink drain

how to replace a bathroom sink drain

Replacing a Bathroom Sink Drain Collar

?·?Pack the underside of the strainer flange with fresh plumbers' putty or apply a continuous roll of putty around the sink drain opening. Drop the strainer into the drain opening and then slip on the rubber gasket from underneath the sink and screw on the locknut. Tighten the nut as much as you can by hand and then finish the job with lovetiktokhere.com://lovetiktokhere.com You simply slip a nut onto the waste drain and press it against the other pipe, then hand tighten the nut. No washers are required here. Next, find the washer that will fit onto the drain under the sink. You’ll note one of them is much too loose, but the other one fits just right. Place a slip joint nut on the pipe first, followed by the lovetiktokhere.com://lovetiktokhere.com

A bathroom sink pop-up stopper is a very convenient feature, and while the installation is usually easy, occasionally the process is complicated due to variations in the fixture or fittings. If you need to install a new pop-up drain for any reason, these instructions will simplify the process. NOTE: In this example, the parts are being installed while the sink is removed from the vanity. In practice you may be installing the pop-up drain on a sink that is already in place.

Loosen and remove the P-trap from the branch drain and sink drain tailpiece, using channel-type pliers. Next, remove the old pop-up assembly, if there is one. Use channel-type pliers or a basin wrench to remove rdain mounting nut from the tailpiece on the old drain assembly, then lift the assembly clear of the sink. Clean the sink thoroughly of debris and old plumber's putty.

Disassemble the pieces of the new pop-up assembly, and unscrew and remove the mounting nut from the drain tailpiece. Install the plastic washer then the rubber washer and push them all the way down on top of the mounting draln, as sjnk here.

Apply a thin layer of pipe joint compound to the top side of the rubber washer that will fit against the sink. Using joint compound on the rubber will ensure that it seals against the bottom of the sink drain opening. While pipe joint compound is not strictly necessary, without it you might have trouble getting the eink to seal. Apply a generous bead of plumber's putty to the underside of the flange on the sink drain ring.

The putty will help the upper part of the drain assembly seal against the sink drain opening. If you do not have plumber's putty or cannot use it on your type of sink, then you can use silicone caulk. Some pop-up assemblies come with a foam or rubber gasket to use in place of plumber's putty or bbathroom. Scoop out a ball of plumber's putty and roll it in your hand to form a long rope, then lay the rope around the edge of the drain ring.

Push the pop-up drain tailpiece assembly up what are baby boomers interested in the drain opening from under the sink as high as you can.

While holding the drain piece in place, fit the drain ring into the opening from the top of the sink, and thread the ring onto the drain tailpiece as far as you can by hand.

Make sure the pieces are threaded bow and are not cross-threaded. For now, it only needs to be hand-tightened enough to hold it in place. From under the sink, hold the drain tailpiece with one hand and tighten the mounting nut upwards toward the bottom of the sink. Make sure the opening in the tailpiece where the pop-up pivot lever will fit is how to replace a bathroom sink drain straight back toward the wall.

Tighten the mounting nut with channel-type pliers while continuing to hold the tailpiece in place. Do not over-tighten this nut, but make sure it is secure enough so that the drain assembly does not spin in the drain opening.

Scrape up the oozed out plumber's putty from around the drain opening, and put it back into the container. As long as it's clean, it's perfectly good to reuse. Push the pop-up stopper down into the drain opening inside the sink, making sure the hole in the linkage is facing toward the back of the sink.

Insert the pivot rod into the opening in the side of the tailpiece from under the sink. Usually, there is a plastic washer on each side of the plastic ball.

You should be able to feel the tip of the pivot rod slide through the opening in the stopper how to replace a bathroom sink drain inside the drain assembly. Screw the pivot rod nut onto the threaded fitting on the side of the tailpiece, so the ball is secured to the tailpiece. Push the pivot rod up and down to make sure the stopper goes up slnk down freely in the drain.

If the pop-up is working properly, you can tighten the nut hand-tight. If the pop-up is not working, reposition the stopper and pivot rod so the pieces connect properly. Feed the vertical pop-up lever down through the hole behind the spout of the faucet. Before connecting replqce horizontal pivot rod to the vertical lever, make sure your stopper is in the fully up open position.

From below the sink, attach the connecting strap to the end of the vertical pop-up lever. Tighten the screw how to hang an american garden flag the connecting strap to secure it to the pivot rod. Connect the vertical strap to the horizontal pivot rod by threading the spring clip onto the rod; one end of the clip attaches on each side of the strap.

Check to make sure that the pop-up stopper opens and closes fully what is charoset at passover the drain opening. Finish the job by reconnecting the P-trap to the drain pipe and drainn tailpiece. Check for leaks by closing the stopper, filling up the sink, then opening the stopper and letting the water drain out while you look for leaks from below.

Actively scan device characteristics for identification. Use precise geolocation data. Select personalised content. Create a personalised content profile. Measure ad performance. Select basic ads. Create a personalised ads profile. Select personalised ads. Apply market research to generate audience insights. Measure content performance. Develop and improve products. List of Partners vendors. Materials Pop-up drain assembly Pipe joint compound Plumber's putty.

Remove the Old Drain Assembly Loosen and remove the P-trap from the branch drain and sink drain tailpiece, using channel-type pliers. Related Topics. Plumbing Repair. Show Full Article. Your Privacy Rights. To change or withdraw your consent choices for TheSpruce. At any time, you can update your settings through the "EU Privacy" link at the bottom of any page.

These choices will be signaled globally to our partners and will not affect xrain data. We and our partners process data to: Actively scan device characteristics for identification. I Accept Show Purposes.

Step 1: Install Pop-up Drain

2 days ago?·?Turn off the water, and clear the area under the sink to prepare to replace your current drain pipes. Move a light close to the area to illuminate your work. Set a bucket under the lovetiktokhere.com://lovetiktokhere.com ?·?How to install a sink drain with rless bathroom sink pop up drain how to install a drop in kitchen sink bathroom sink popup and stopper problems maintain plumbing for offset kitchen sink How To Install Bathroom Sink Drain Queen Bee Of Honey DosHow To Fix A Leaky Sink Trap HomeHow To Replace A Kitchen Read More»lovetiktokhere.com

You probably haven't spent a lot of time thinking about your bathroom sink drain pipe. It's just one of those things, hidden away, that serves its purpose with little attention. And then, one day, it happens. Your sink drain leaks, or it breaks. Perhaps the water is backing up in your sink, and you know it's clogged.

Even if you've never touched a pipe in your life, you can repair and replace the drain pipes on a bathroom sink. Just set aside an hour or so when you can concentrate on your work. Point a bright light at the sink plumbing. Turn the water on and watch the pipes beneath the sink. Grab each connection in turn with a fresh paper towel and hold a few seconds to determine where the drain is leaking.

Inspect the leaking area carefully to determine if a fitting is loose and causing a drip. Tighten loose couplings to eliminate the moisture. If the coupling seems snug but the leak continues, unscrew the coupling to detach the joint. Clean the pipe threads, on either end, with a clean cloth. Replace old gaskets and fittings before reassembling. Loosen the nut that secures the sink basket underneath the basin. Use a wrench to break free stubborn connections. Insert a screwdriver or pliers through the cross-piece, working from the top of the sink.

Use the tool to hold the basin in place while you remove the nut underneath. Strip off the old gasket putty around the installation area. Scrub the opening on both the bottom and the top of the sink with a stiff-bristled brush.

Rinse with hot, soapy water. Peel off the backing on the sticky side of a replacement sink basket gasket. Center the gasket directly over the sink's drain hole before pressing in place. Follow with the sink basket, ensuring it is where you want it before you set it to prevent ruining the seal. Push a new washer, followed by a nut, on the sink basket piece that drops below the sink. Squirt or spread plumber's putty or another approved sink sealant over the threads.

Attach the drain connection, hand-tightening only. Test your drain with a little water before removing the bucket underneath the sink. Turn off the water, and clear the area under the sink to prepare to replace your current drain pipes. Move a light close to the area to illuminate your work. Set a bucket under the P-trap. Loosen and remove the couplings on either end of the P-trap. Support the assembly and carefully lower before dumping the waste water into the bucket. Clean the pipe threads on the sink drain piece hanging down from the sink and on the pipe emerging from the main drain pipe in the wall.

Scrub with a stiff-bristled brush and hot, soapy water. Follow with a clean rag to remove residue. Assemble a new P-trap kit. Insert washers and gaskets where instructed. Raise the trap into place, underneath the sink. Tighten the couplings on either end to secure the trap. Run water through the pipes carefully before removing the bucket and replacing the items previously removed from under your sink.

Karie Fay earned a Bachelor of Science in psychology with a minor in law from the University of Arkansas at Monticello. After growing up in construction and with more than 30 years in the field, she believes a girl can swing a hammer with the best of them. She enjoys "green" or innovative solutions and unusual construction. By Karie Lapham Fay.

Related Articles. Treat old metal pipes or chrome pipes the same as PVC. The only difference is the material of which they are made.

P-traps are designed to hold water at all times to prevent sewer gasses from entering the home from the drain. Avoid any contact with this water as it contains bacteria and germs along with waste matter.



Plus d'articles dans cette categorie:
<- Wasps nest how to get rid of them - How to track sales in excel->

0 reflexions sur “How to replace a bathroom sink drain

Ajouter un commentaire

Votre courriel ne sera pas publie. Les champs requis sont indiques *