How to fix ps3 controller ps button
My PS3 won't recognize motion controller?
Sep 14, · PS3 controller buttons pressing themselves fixI take a look at the random button presses and general PS3 controller problems and offer a simple lovetiktokhere.com this f. Sep 19, · Fix a glitchy broken PS3 controller. If your buttons don't work or they make the menu go on the fritz, this is likely the repair you need. The only tool re.
This article was written by Travis Boylls. Travis has experience writing technology-related articles, providing software customer service, and in graphic design.
He studied graphic design at Pikes Peak Community College. The wikiHow Tech Team also followed the article's instructions and verified that they work. This article has been viewed 44, times. This wikiHow teaches you how to fix a PS3 controller. One of the most common problems with PS3 controllers is random button pushes. There is a fairly easy fix to this problem, but it will require disassembling your controller. Other problems you may encounter are dislodged analogue sticks, and how to fix ps3 controller ps button damage.
Cookie Settings. Learn why people trust wikiHow. Download Article Explore this Article methods. Related Articles. Method 1 of Remove screws from the back of the controller. There are five screws holding the controller together.
There are two on the top and bottom of both sides, and one on the top middle. Remove the back. You may need to pry open the controller how to monitor cpu temperature while gaming a flat head screwdriver.
Open it what is seventy in french the bottom and carefully tilt it towards the top shoulder buttons. Be very careful that you don't accidentally dislodge the R2 or L2 trigger buttons while removing the back. They can be pain to put back on. Remove the battery. The battery is the grey square piece on the back of how to start a small industry motherboard.
You don't need to disconnect the battery. You can just pull it up out of it's holder and move it to the side. If you do decide to disconnect the battery, pull on the white plastic part that the wires are connected to.
Do not pull on the wires. Remove how to fix ps3 controller ps button screw on the motherboard. The motherboard screw is located on the bottom of the motherboard next to the analogue stick. Remove the motherboard. Carefully pull the motherboard up and tilt it away from the shoulder buttons.
Once again, be careful not to accidently dislodge the R2 and L2 trigger buttons. Lift the green ribbon and pull it back. The green ribbon is located at the top of the controller front. It's above the hole where the left analogue stick goes. Place a flat head screwdriver under the ribbon and carefully lift it up over the two plastic pins that are sticking up out of the controller.
Be careful not to tear or damage the ribbon. You will see a strip of black foam underneath the ribbon. Remove the black foam strip. Over time, the foam strip gets compressed and the connectors on the ribbon aren't able to make contact with the motherboard. This is why the controller is not working properly. Place tape on the bottom of the black foam strip. For the best results, cut a strip of thick double-sided tape the same length and width as the black foam strip.
Place it under the foam strip. Use scissors to cut off any excess tape from the sides. If you don't have thick double-sided tape, you can cut about an inch-and-a-half of black electrical tape and roll it up into a tube. Replace the foam strip. With the tape underneath the foam strip, you can now place the foam strip back under the ribbon.
Replace the ribbon. Pull the ribbon over the foam and place the two holes over the pins that are sticking up out of the controller. Make sure it is firmly in place.
Clean the ribbon. Since the controller is open, it's not a bad idea to use a tissue or cotton swap to wipe any dust away from the ribbon. Clean the motherboard connector. If you look at the motherboard, you will see a box that is a darker shade of green with some metal connectors sticking out of it.
It's above the left analogue stick. This is where the motherboard connects to the ribbon. Use a tissue or cotton swap to wipe the connectors on the mother board. Replace the motherboard. Carefully place the motherboard back in it's place with the analogue sticks freely able to move through the holes. Screw the motherboard back in place. Using the same screw you took out of the motherboard, screw it back in at the bottom next to the right analogue stick.
Replace the battery. The motherboard has a plastic holder on it's back that holds the battery in place. Place the battery back in the holder. Replace the controller back. To replace the controller back, place the the thin part that goes in between the two shoulder buttons at the top of the controller in place. Carefully tilt the back over the R2 and L2 trigger buttons and firmly push it back in place at the bottom of the controller. Be careful not to accidentally dislodge the R2 and L2 trigger buttons.
Replace the screws on the controller back. There are five screws that hold the controller together. Replace the two on the sides, and the one in the middle. Your controller is now fixed. Method 2 of What is a bland diet for diverticulitis battery is the large grey square on the back of the motherboard.
If you do decide to disconnect the battery, pull on the white plastic part connected to the circuit board. Don't pull on the wires. Once again, be careful not to accidentally dislodge the R2 and L2 trigger buttons.
Place the plastic stick back on the metal rod. There is a D-shaped metal rod that sticks up out of the motherboard. Place the plastic analogue stick back on the metal rod. Be very careful not to dislodge the R2 and L2 trigger buttons. Method 3 of Power off the controller immediately. If the controller gets wet, turning off the power immediately will prevent the circuit board from shorting out.
Disconnect the battery. To disconnect the battery, pull the white plastic piece that connects to the motherboard. Pull on the plastic piece. Place the controller under a lamp, fan, or window. This will help the water in the controller evaporate. Wait at least 24 hours. To ensure the controller is completely dry wait 24 hours, or longer.
Log In to GameFAQs
Apr 22, · The reset procedure is as follows: Turn off your PS3 and disconnect the controller The reset button is located at the back of the controller. You will need a paperclip to press lovetiktokhere.comted Reading Time: 40 secs. Nov 06, · I plugged the joystick in the PS3 through the USB port and lo and behold, it acted like a regular controller (without the sixaxis/DS3 functions of course--oh, and no PS button). I assume the PS2 controller will be the same way once my PS2-PS3 controller adapter comes in the lovetiktokhere.comted Reading Time: 1 min. Press the reset button on the back of the controller (may need to use a pin), then link it to the PS3 with USB cable and press Ps button on controller. This will pair the controller to the PS3.
This is a split board - You can return to the Split List for other boards. Log In Sign Up. Keep me logged in on this device Forgot your username or password? Don't have an account? Sign up for free! What do you need help on? Cancel X. Topic Archived. Sign Up for free or Log In if you already have an account to be able to post messages, change how messages are displayed, and view media in posts.
User Info: JushtFinisht. User Info: wheepitup. You could get a bluetooth remote control, it has a ps button on it. User Info: MourningReigns. I don't really think there is anything you can do if you don't have that button unless you just eject the game.
User Info: InfernoSD. If you have a keyboard plugged in, the Windows or equivalent key may function as PS Button. User Info: bsballa The Windows button on a keyboard works. Police: You're completely against them until you need them. But if they don't even slightly agree with your story, you are completely against them again. Tried the keyboard method--didn't work, but mine was USB, so maybe it has to be a bluetooth device for it to work. More topics from this board Controller Dpad button is acting like its permanently pressed?
Looks fun. Why can't I connect to PSN? Tech Support 1 Answer Some games won't load but some do? General 1 Answer How do I install games? General 2 Answers. Ask A Question. Browse More Questions. Keep me logged in on this device. Forgot your username or password? SO to make it in question form How do I do it?!?! User Info: wheepitup wheepitup 9 years ago 2 You could get a bluetooth remote control, it has a ps button on it. User Info: MourningReigns MourningReigns 9 years ago 3 I don't really think there is anything you can do if you don't have that button unless you just eject the game.
User Info: bsballa09 bsballa09 9 years ago 5 The Windows button on a keyboard works. Where do i buy replacement analog sticks for a DS3? What are you currently do playing?
Part Tech Support. Some games won't load but some do? How do I install games?
<- How to piss off your designer friends - How to print on a mug->